Archive

Archive for January, 2011

Still working

January 27th, 2011 admin 3 comments

I wanted to post a picture of what the inside of the mold looks like while the resin is curing. I’m also posting a picture of a pre-aged paint job, using a darker blue and shinier yellow. I haven’t nailed down a crackle technique I really like yet. I have a self-imposed goal of the end of January to get this mask completed, because I’d like to move on to another costume project in February, so I might just finish this one off with the crackle glaze I have now, and save a casting for when I someday find the perfect technique.

The inside of the resin-coated mold

Happy with the colors, still not sure how to age it

Categories: Uncategorized Tags:

One step too far

January 21st, 2011 admin No comments

Ok, so now I know what NOT to do. Since I am still considering this a prototype, I decided to experiment with pushing the antiquing a little further, and applying a really thick coat of the crackle glaze. I hoped it would produce a more prominent craquelure pattern. What actually happened was that a lot of it ended up pulling away and flaking off. I applied the dark wash anyway, just to see what it would look like. You can see the results – it looks more dirty than antiqued. Now I know!

Dirty.

Scary, but not the look I'm going for.

Categories: Doctor Who Tags:

Prototype trimmed, painted

January 16th, 2011 admin No comments

I’m calling this first mask a prototype, as I’m trying out paint colors, techniques, trim lines, etc. After trimming with a dremel, I had to slightly widen the mask by softening in hot water, reshaping, then dipping in cold water to set.

Then I added trim along the edge by splitting an old cable, stripping out the wires inside, and using Gorilla Glue to adhere it.

As far as paint, I’m going to darken the blue next time, and maybe add some metallic gold to the yellow. The crackle glaze worked, but again, the cracks are smaller than I’d like. I THINK it’ll work better if I can get a thicker coat down, because the crackles were perfect where the glaze dried on my palette.

Please excuse the distortion in the photos – these were taken with my phone.

bright colors, they'll darken with the glaze and washes

a view of the inside, showing the trim

a view of the inside, showing the trim and proving it can be worn

after several washes of black and brown - trying to bring out the cracks and weather it

I like this view for showing the dimensionality of the cheeks

The cracks are much smaller than I wanted - I don't think you can even see them in pictures.

Categories: Doctor Who Tags:

First pull from new mold

January 10th, 2011 admin No comments

First layer of oogoo down.

I was somewhat worried about taking a mold of my cracked sculpey mask. I patched the cracks with fresh sculpey so hopefully the silicone wouldn’t flow into them (maybe I should’ve used an epoxy, but I was anxious to get the silicone down during a brief warm-spell last week). As it turns out, they didn’t pose TOO much of a problem, but I’ll address that later. I was able to get a couple layers of my modified oogoo silicone down while it was warm enough to work in the garage (this stuff stinks).

Once that cured, I added a mother-mold of plaster bandages, and finally peeled everything off to see how I did. The silicone did flow into a couple of the bigger cracks, but it wasn’t too bad. My worst mistake was cutting out the eyes from the clay. This created a problem when trying to release the mold from the master, as the deep sockets grabbed on tight and didn’t want to let go. Patience and persistence won out, though, and after cleaning any clay bits from the mold I was ready to slush some resin in there.

Second oogoo layer down

I’m using a white, 1:1 ratio casting resin from Alumilite. Since my test casting from the old mold came out with a ton of bubbles, I wanted to be much gentler this time around with my slushing. The resin came with little 2oz Tbs cups for measuring, so I used 3 4ozTbs batches which seemed to build up a decent thickness. I’d mix up a batch, pour it into the mold, and slowly roll it around, trying to cover the entire surface evenly. My biggest fear was that the nose would collect all the extra resin from each layer, and be filled up entirely at the end. With each layer I was very conscious of not letting it collect there, and I think it worked out. I let it cure for about 30 minutes before de-molding. As you may or may not be able to tell from the image, there were NO bubbles this time! The worst problem is a “crack” in the chin area that was present in the master, and was deep enough that it didn’t get covered with resin in the mold. Hopefully it will be trimmed off when I decide on the final trim line. I’ll try to correct this in the mold before I take the next cast.

Mother mold

This weekend I also stopped at Michael’s and picked up a couple different “crackle” mediums. Lynette had tried a spray version on her first mask, which did not give the desired effect. The ones I picked up were acrylic. One was to be used between two paint layers, where the top layer would crackle, revealing the base color. The other is a glaze or varnish, where you then apply a wash to bring out the crackle detail. The glaze gave the best results, looking more like aged porcelain, whereas the one that goes between layers looked more like paint chipping off antique wood furniture. I’m optimistic about the glaze, even though the cracks are smaller than I would’ve liked.

First pull from the new mold

Categories: Doctor Who Tags:

New Year’s Resolution

January 4th, 2011 admin No comments

These kinds of things work best when they’re declared publicly, so here goes: R2 will AT LEAST get a frame and legs this year – as they say on American Chopper, “rolling chassis.” I have a lot planned for other projects, including finishing the Clockwork Droid mask, crafting various other costume pieces for and with Lynette, and building my own costume for Dragon*Con 2011, but I WILL make R2 progress. 2010 was a complete bust for the little overweight glob of grease, but I have some new tools that will make the job easier (or that’s what I’ve been telling myself). I’ve been rediscovering my passion for this stuff, and I can’t let that go to waste just reading the RPF til 1am every night.

Categories: R2D2, Star Wars Tags: